Free tool. No signup. Works on your phone.
Find out if your plants are getting too little, too much, or the right amount of light each day. Enter your PPFD, or your light watts and tent size, and get your DLI with a clear target for your growth stage.
See how your canopy responds to the light with a photo health report in MasterGrowbot AI for iOS or Android. Eligible new Pro subscribers can try 3 days free.
Quick answer
Good starting targets for cannabis are 10 to 20 DLI for seedlings and clones, 25 to 40 in veg, and 35 to 45 in flower without added CO2. A flowering canopy at 900 PPFD for 12 hours receives 38.9 DLI, which is on target.
Growth stage
What do you know about your light?
PPFD at the canopy
µmol/m²/sUse a PAR meter reading or the PPFD map from your light maker at your hanging height.
Hours of light per day
12 hDaily light integral
38.9
DLI (mol/m²/day)
900 PPFD for 12 hours
Target for flower: 35 to 45 DLI
Your daily light is in the target range for flower. Hold it steady and watch the top leaves.
Snap a photo of your canopy in MasterGrowbot AI for a plant health report, and save your light settings in the grow journal so you can repeat a good run.
Free download. Eligible new Pro subscribers can try 3 days free.
This DLI chart redraws for the growth stage you picked above. Green cells are inside the flower target of 35 to 45 DLI. The outlined cell is closest to your setup.
| Hours / PPFD | 200 | 300 | 400 | 500 | 600 | 700 | 800 | 900 | 1000 | 1100 |
|---|---|---|---|---|---|---|---|---|---|---|
| 12 h | 8.6 | 13.0 | 17.3 | 21.6 | 25.9 | 30.2 | 34.6 | 38.9 | 43.2 | 47.5 |
| 14 h | 10.1 | 15.1 | 20.2 | 25.2 | 30.2 | 35.3 | 40.3 | 45.4 | 50.4 | 55.4 |
| 16 h | 11.5 | 17.3 | 23.0 | 28.8 | 34.6 | 40.3 | 46.1 | 51.8 | 57.6 | 63.4 |
| 18 h | 13.0 | 19.4 | 25.9 | 32.4 | 38.9 | 45.4 | 51.8 | 58.3 | 64.8 | 71.3 |
| 20 h | 14.4 | 21.6 | 28.8 | 36.0 | 43.2 | 50.4 | 57.6 | 64.8 | 72.0 | 79.2 |
| 24 h | 17.3 | 25.9 | 34.6 | 43.2 | 51.8 | 60.5 | 69.1 | 77.8 | 86.4 | 95.0 |
| Stage | PPFD | Light hours | DLI target |
|---|---|---|---|
| Seedlings and clones | 150 to 300 | 18 hours | 10 to 20 |
| Vegetative | 400 to 600 | 18 hours | 25 to 40 |
| Flower | 800 to 1,050 | 12 hours | 35 to 45 |
These are starting ranges for rooms without added CO2. Cultivar, plant health and room conditions all move the ideal number, so change intensity in small steps.
PPFD is how much usable light lands on your canopy each second. Think of it as how hard it is raining. DLI is the total light your plants collect over the whole day. Think of it as how much water ends up in the bucket. A gentle rain for 18 hours and a heavy rain for 12 hours can fill the same bucket, and that is why growers who only look at watts or percent on the dimmer often miss what the plant is really getting.
Cannabis is a high light crop, but it can only use so much. Too little daily light gives you stretchy plants, thin stems and airy flowers. Too much gives you bleached tops, leaf edges that curl up like a taco, and nutrient problems that are really light stress in disguise. The goal is to land inside the range your plants can use at their current stage, then hold it there.
Light does not work alone. A plant under strong light drinks and transpires more, so your temperature and humidity have to keep up. After you set your light here, check your room with the free VPD calculator so the two work together.
Step 1: Pick your growth stage. The calculator sets a typical light schedule for that stage, 18 hours for seedlings and veg and 12 hours for flower. Change the hours if you run something different, such as 20 hours for autoflowers.
Step 2: Enter your PPFD if you know it. The best source is a PAR meter held at canopy height. The next best is the PPFD map your light maker publishes for your hanging distance. Use the average across the canopy, not the hot spot in the center.
Step 3: No PPFD number? Estimate it. Choose your light type, enter the actual watts it draws from the wall, and pick your tent size. The result is an average estimate. It is good enough to tell you whether you are far off, and it is honest about being a rough guide.
Step 4: Read the result and make one change. If your DLI is low, raise intensity or lower the light a little. If it is high, dim the light or raise it. Change one thing, wait three or four days, and look at the newest growth before you change anything else.
Step 5: Let the plant confirm it. Numbers get you close. The leaves tell you if you are right. Take a canopy photo in MasterGrowbot AI for a plant health report, and keep your light settings in the grow journal. Download it free on iOS or Android. Eligible new Pro subscribers can try 3 days free.
Trusting the watts on the box. Many lights are sold by an "equivalent" wattage that has nothing to do with what they draw or deliver. Use the actual wall watts from the spec sheet.
Running flower intensity on seedlings. Young plants need a fraction of the light a flowering canopy does. Blasting them is one of the most common reasons seedlings stall in week one.
Raising light without raising everything else. More light means more water, more feed and more heat to manage. If the top leaves pale or curl after you turn the light up, back off and read the LED grow lights guide before pushing again.
Changing hours in flower. Photoperiod plants need 12 hours of unbroken darkness to keep flowering. Adjust intensity instead, and see the cannabis light schedules guide for the details.
For more on every stage of the grow, visit the cannabis grow guides hub.
DLI means daily light integral. It is the total amount of usable light a plant receives in one day, measured in moles per square meter per day. It combines how bright the light is (PPFD) with how many hours it runs, so it is the fairest way to compare an 18 hour veg schedule with a 12 hour flower schedule.
Multiply PPFD by the hours of light per day, then multiply by 0.0036. For example, 900 PPFD for 12 hours is 900 x 12 x 0.0036 = 38.9 mol per square meter per day. The grow light calculator on this page does the math for you and compares the result to a target range for your growth stage.
Most photoperiod cannabis does well at 800 to 1,050 PPFD across the canopy in flower on a 12 hour schedule without added CO2. Seedlings and clones need far less, around 150 to 300, and plants in veg usually sit at 400 to 600. Raise intensity in steps and watch the top leaves for bleaching or tacoing.
Only roughly. Watts measure the power a light draws, not the light that reaches the leaves. This calculator estimates average PPFD from actual wall watts, the fixture type and your tent size. For a real number, use a PAR meter or the PPFD map from the light maker at your hanging height.
With a newer LED bar light, roughly 500 to 700 actual watts covers a 4x4 foot flowering canopy at 800 to 1,050 PPFD. Older or less efficient lights need more watts for the same result. Enter your light and tent in the calculator to see an estimate for your setup.
Yes. MasterGrowbot AI lets you photograph the canopy and get a plant health report that flags signs of light stress, such as bleached tops and upward leaf curl, and it keeps your light settings in the grow journal. Download MasterGrowbot AI free. Eligible new Pro subscribers can try 3 days free.
Snap a photo. Save your plant. Download MasterGrowbot AI for plant health reports, a grow journal and daily tasks. Eligible new Pro subscribers can try 3 days free.